中文 | English    
锁相放大器
前置放大器
光学斩波器
电子学插件
信号发生器
频率分析仪
功率放大器
精密滤波器
LCR测试仪
交流电压表
协议分析仪
计测系统
TOF-MS
膜厚测量仪
信号平均器
其他
资料下载
首页 | 产品展示 | 光学斩波器 | 分离式光学斩波器 | 光学斩波器
厂商名称:Signal Recovery
商品名称:光学斩波器
商品型号:651-1
简单信息:Signal Recovery 原隶属于美国EG&G公司,现隶属于美国AMETEK集团公司,是专业生产微弱信号检测类产品的制造商。其锁相放大器、光学斩波器、BOXCAR等始终处于行业的领先水平。

Model 651-1
Dual Aperture Light Chopper
The model 651-1 uses the standard head. This is a dual port design allowing two optical beams to be modulated simultaneously at different frequencies, f1 and f2. Two reference (sync) outputs are made available at the control unit, corresponding to f1 and f2, for use with signal recovery processing electronics, such as a lock-in amplifier.

Two small blanking plates are provided with the standard head and one of these allows either the top port or the bottom port to be blanked off to reduce the effect of any stray light passing through an unused path. The second plate provides some measure of beam restriction when using large diameter beams on the higher frequency (and therefore smaller aperture) port. The standard head is supplied complete with a flat base plate to allow the unit to be used in a free standing mode on a bench type surface. A special feature of this support allows the head to be used in the horizontal plane for modulating vertical beams. The base plate can be removed and standard optical mounting supports employed instead if preferred.

Model 651-1 Mechanical Dimensions


Model 651-1 Mechanical Dimensions

Model 651-1 Blade Dimensions

Model 651- Blade Dimensions

Model 651-1 Specifications
Operation
Frequency 10 Hz to 3200 Hz
    outer sector 100 Hz to 3200 Hz
    inner sector 10 Hz to 320 Hz
Control
    manual Digital push-button
    external Application of 0.5 V to 10 V sine or squarewave, 50 Hz to 3200 Hz to EXT SYNC BNC connector
Internal Frequency
    accuracy ±30 ppm at 25 °C
    stability ±50 ppm/ °C (range 10 °C to 30 °C)
Jitter (measured pk-pk and presented as a % of a full cycle)
    outer sector
        100 to 200 Hz blade only: 0.2%; blade + electronics: < 7%
        200 to 400 Hz blade only: 0.2%; blade + electronics: < 4%
        400 to 2500 Hz blade only: 0.2%; blade + electronics: < 1.5%
        2500 to 3200 Hz blade only: 0.2%; blade + electronics: < 2%
    inner sector
        10 to 20 Hz blade only: 0.2%; blade + electronics: < 0.7%
        20 to 40 Hz blade only: 0.2%; blade + electronics: < 0.4%
        40 to 250 Hz blade only: 0.2%; blade + electronics: < 0.2%
        250 to 320 Hz blade only: 0.2%; blade + electronics: < 0.3%
Lock indication green LED when locked - can be extinguished
Settling Time <40 s nominal
Outputs
Sync Out 1 10 V pk-pk squarewave at outer sector chopping frequency, 50 - 3200 Hz
Sync Out 2 10 V pk-pk squarewave at inner sector chopping frequency, 10 - 320 Hz
Connectors BNC
Impedance 10 kΩ. Note that although the output voltage is 10 V pk-pk, the high output impedance means that the outputs can be directly connected to the Reference Frequency input of any SIGNAL RECOVERY lock-in amplifier without causing problems.
Power Requirements 110 V AC, 50/60 Hz or 220/240 V AC, 50/60 Hz supply. State which voltage is required when ordering
Dimensions
Controller 6.6" wide x 3.1" high x 9.3" deep
(168 mm wide x 79 mm high x 236 mm deep)
Chopper head, overall, inc. base and feet 4.8" wide x 5.9" high x 2.8" deep
(122 mm wide x 150 mm high x 72 mm deep)
Options Model 653A 2 m (6'6") extension cable
| 联系方式:010-65202180 传真:010-65202182 北京三尼阳光科技发展有限公司 .版权所有 | 技术支持:尚品中国